MATEK F405-SE AIO FLIGHT CONTROLLER

F405-SE

  • $58.95

Will be in stock after
Add to Wishlist

LOOKING TO BUY A MATEK F405-SE AIO FLIGHT CONTROLLER IN AUSTRALIA? YOU'VE COME TO THE RIGHT PLACE. ANY QUESTIONS? PLEASE LIVE CHAT US, WE'RE HERE TO HELP!

CHECK OUT OUR GREAT RANGE OF MATEK PRODUCTS HERE

Specifications

  • MCU: 168MHz STM32F405RET6
  • IMU: MPU6000 (SPI)
  • Baro: DPS310 (I2C)
  • OSD: AT7456E (SPI)
  • Blackbox: MicroSD slot (SPI)
  • VCP & 6x Uarts, 1x Softserial_Tx supported
  • 9x PWM outputs (7x Dshot compatible with BF/INAV)
  • 2x I2C
  • 3x ADC (voltage, current, RSSI)
  • 4x RX6 pad(one per corner) for BLheli32 ESC telemetry
  • 4x individual ESC power/signal pads
  • 1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
  • 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)
  • Built in inverter on UART2-RX for SBUS input
  • PPM/UART Shared: UART2-RX
  • Vbat filtered output power for VTX
  • Camera control: Yes
  • Smartaudio & Tramp VTX protocol: Yes
  • DJI FPV OSD protocol: Yes
  • WS2812 Led Strip: Yes
  • Beeper: Yes
  • RSSI: Yes

PDB Specifications

  • Input: 6~36V (2~8S LiPo) w/TVS protection
  • PDB: 4x35A (Max.4x46A)
  • BEC: 5V 2A cont. (Max.3A)
  • LDO 3.3V: Max.200mA
  • Current Sensor 184A (Scale 179 in INAV/BF)
  • Battery Voltage Sensor: 1K:10K

Firmware

  • INAV: MATEKF405SE
  • BetaFlight: MATEKF405SE
  • ArduPilot: MATEKF405-WING
  • Physical
  • Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
  • Dimensions: 36 x 46 mm
  • Weight: 10g

Package Includes

  • 1x F405-SE
  • 6x silicon grommets M4 to M3
  • 1x FR4 PCB Plate 36*36*1mm
  • 1x Rubycon ZLH 35V/470uF (Low ESR)

For manual wiring and layouts please see Matek product page

Important Notes: 

  • Before soldering or mounting any flight controller, connect it to your PC and verify operation
  • Incorrect soldering techniques will damage this board and void warranty. Please use the correct sized tip, temperature and technique. Temp controlled soldering irons (such as the TS100) are available for under $100 and will make soldering much easier.
  • Lifted pads are a result of incorrect soldering techniques or excess mechanical pressure and will not be covered under warranty. 
  • USB ports must be handled with care, breakage of usb ports are not covered under warranty
  • Always use a smoke stopper before powering your build for the first time. 

LOOKING TO BUY A MATEK F405-SE AIO FLIGHT CONTROLLER IN AUSTRALIA? YOU'VE COME TO THE RIGHT PLACE. ANY QUESTIONS? PLEASE LIVE CHAT US, WE'RE HERE TO HELP!

CHECK OUT OUR GREAT RANGE OF MATEK PRODUCTS HERE

Customer Reviews

Based on 1 review Write a review

We Also Recommend