HolyBro Shuriken X1
The Shuriken X1 is a ultra high performance, value packed, FPV racing X frame built with high quality components usually found on much more expensive frames on the market.
Every component has been well thought out for high speed crashes, tuned, tested and re-tuned for optimum flight performance.
The Shuriken X1 comes with the latest F3 flight controller; on screen display, pdb and video transmitter all packaged onto one board which means fast replacements with minimal soldering so you spend less time wrenching and more time racing.
The all in one design also means that the stack height of the Shuriken X1 is kept as low as possible for a better centre of gravity while still allowing the for a Gopro Session mounted at a 35 degree angle.
If you are looking to step up your racing without the hassle of building your own X frame quad this is the perfect solution!
- Flight Controller : 32-bit F3 Flight Controller , MPU6050 Gyro/Accelerometer
- ATmega328P with Arduino Bootloader(minim OSD) MAX7456
- OneShot125 BLheli-S S 30A / 40A burst BLHeli ESC's
- 2305-2600kv Motors (T-MOTOR F40V2)
- 5" props, 200mm motor to motor.
- Input voltage 7v to 42v.
- PCB Maximum Continuous Current 120A
- Filtered voltage output - output 5.2v 2A
- Weight: Approx 370g without battery
- Full 3K Carbon Fiber
- Nickel-plated 12.9 screws
- Easy grip black anodized spacers
- FC;OSD;PDB;VTX and voltage/current sensor All In One (AIO) Board
- 5.8GHz, 25mw, 40 Channel Vtx with built in push button switching and channel display
- High quality CP antenna
- Integrated MWOSD (firmware V1.5 preloaded)
- 1/3 SONY Super HAD II CCD, PAL, 600TVL Camera, 2.5mm Lens
- FrSKY, FLYSKY or DSMX receiver included (select from drop down required RX before adding to cart)
- RGB LED board
- Two mounting positions for the FPV Camera: one for a 0°~40° view angle, a second mounting position for 35°~70° view angle
- Included TPU GoPro Session mount. HD Camera angle 35°
- BetaFlight 3.0 Pre-loaded and tuned
- 1 x Shuriken X1
- 1 x Flight Controller (AIO board)
- 1 x PDB (AIO board)
- 1 x 2.4g Receiver (FrSKY XSR***, DSMX or FLYSKY X6B**)
- 4 x ESC's
- 4 x 2305 Motor
- 4 x 5x4.5 Inch Propellers
- 1 x 40CH VTX (AIO board)
- 1 x 600TVL Cam
- 1 x 5.8G 4 skew planar antenna
- 1 x Gopro session protector (TPU 3D Print) *
- 2 x Battery straps
- Battery (Recommended FMR 1300 4s 95c or R-Line 1550 4s 95c)
- Battery Charger
- 2.4ghz Remote Control Transmitter (FrSKY***/DSMX/FLYSKY**)
- FPV headset/monitor (not required for line of sight only flying)
*Go Pro Session not included
** FLYSKY X6B RX is compatible with Turnigy/FLYSKY i6s, i10 & Evolution radios
*** FrSKY XSR is compatible with FrSKY transmitters (Taranis X9D/X7/Horus or XJT JR module)
IMPORTANT!! Betaflight comes pre-loaded and configured - if you decide to upgrade the firmware on the flight controller please make sure you are well versed in flashing firmware and do a CLI backup first!