ImmersionRC 700mW 2.4GHz Audio/Video TXTX_2G4_700_US
The NexWaveRF based 700mW 2.4GHz audio/video transmitter greatly increases the range of your video link, adding a margin of security over commonly used 5.8GHz transmitters.
Team this TX up with the Fatshark 2.4ghz Modular Receiver for your goggles or either a Duo2400 or Uno2400 for amazing image quality and range (soon to be released).
Built on the same game changing NexWaveRF technology that has made the ImmersionRC 5.8GHz transmitters such a renowned success the 2.4GHz audio/video transmitter is built on this proven technology to offer you the best possible image quality, durability and ease of use.
Sporting roughly the same size and weight as the ImmersionRC's 5.8GHz audio/video transmitters the new 2.4GHz audio/video transmitter brings a few features to market that will allow you to further reap the benefits of choosing ImmersionRC's equipment for your next FPV mission.
The 5V output has been beefed up to handle up to 1.5A of current output, which means you can power, and charge, your HD camera such as a Mobius, straight off of our audio/video transmitter. So no more fiddling with external 5V supplies, just hook it up and be done with it.
The new 700mW 2.4GHz transmitter is designed to run straight off of your main flight-pack and supports a wide voltage input range of 6-25V (2~6s) direct. Due to its extremely low-noise, highly efficient switching regulator, there's no additional heat being generated when running off of higher voltages and the switching regulator's input is well filtered to cope with noise from your speed controller, or other electronics connected within your aircraft.
The NexWaveRF based 2.4GHz audio/video transmitter has a 700mW/28.5dB RF output power, putting it a notch above the commonly available 500mW 2.4GHz transmitters from other manufacturers. It features the same industry standard locking connectors for connecting your battery and camera or audio/video source as featured on ImmersionRC's other products. This makes the new 2.4GHz audio/video transmitter fully compatible with the existing 5.8GHz audio/video transmitters; it can be swapped out directly as all the connectors, and connector pin-outs, are the same. This also applies to the SMA-female antenna connector used.
• 700mW transmitting power (can be used license-free in Europe)
• NexwaveRF based
• 5V 1.5A output for FPV camera and charging
• Small Size
• SMA Antenna Connector
• Onboard quiet switching regulator 2~6s direct capable
- RF Module: NexwaveRF
- Power supply: 6~25V (2S-6S supply)
- Power out (to camera): 5V, 1.5A max
- Transmitting power: 700mW
- Operating Frequency: 2.4GHz 2396, 2410, 2430MHz (USA version
- Dimensions: 57 X 23 X 12 mm
- Weight: 18g (without dipole antenna)
Note: White connector on the back of the transmitter is for connecting an ImmersionRC TinyTelemetry accessory. (adds Telemetry data to the audio channel for Antenna tracking)
Notice: The use and operation of this product in Australia and many other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that you comply with the rules and regulations regarding radio transmitters in your country. NextFPV is not responsible for your actions if you choose to use this product.
We Also Recommend
ImmersionRC rapidFIRE w/ Analog PLUS Goggle Receiver Module
ImmersionRC DUO 5800 V4.2 5.8GHZ A/V Diversity Receiver "Race Edition"
ImmersionRC LapRF Personal Race Timing System - LAPRF1