MATEK F765-WING FLIGHT CONTROLLER

F765-WING

  • $107.95

Only 2 left!
Add to Wishlist

F765-WING Quick Start Guide   (PDF 9M)


FC Specifications

  • MCU: STM32F765VIT6, 216MHz , 512KB RAM, 2MB Flash
  • IMU: MPU6000 (SPI1) & ICM20602 (SPI3)
  • Baro: BMP280 (I2C2)
  • OSD: AT7456E (SPI2)
  • Blackbox: MicroSD card slot (SDIO)
  • 7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
  • 1x Softserial1_Tx (INAV)
  • 12x PWM outputs (S1~S10 support Dshot)
  • 6x ADC (VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2)
  • 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
  • 2x I2C
  • 1x SPI4 breakout
  • Switchable Dual Camera Inputs
  • Switchable 5V/9V(12V) for Camera/VTX
  • High-precision Current Sense
  • ADC VB2 voltage divider: 1K:10K
  • ADC AirSpeed voltage divider: 10K:10K
  • TR/SA VTX control: Yes
  • WS2812 Led Strip : Yes
  • Beeper : Yes
  • RSSI: Yes
  • Analog Airspeed sensor: Yes
  • Digital Airspeed sensor: Yes

FC Firmware

  • INAV Target: MATEKF765
  • ArduPilot(ChiBiOS) Target: MATEKF765-WING

PDB

  • Input voltage range: 9~36V (3~6S LiPo) w/TVS protection
  • 2x ESC power pads
  • Battery Voltage Sensor: 1:10 (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
  • Current Senor: 132A,  3.3V ADC (Scale 250 in INAV,  40 A/V in ArduPilot)

BEC 5V output

  • Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
  • Continuous current: 2 Amps, Max.3A

BEC 9V /12V output

  • Designed for Video Transmitter, Camera, Gimbal ect.
  • Continuous current: 2 Amps, Max.3A
  • 12V option with Jumper pad

BEC Vx output

  • Designed for Servos
  • Voltage adjustable, 5V Default, 6V or 7.2V via jumper
  • Continuous current: 8 Amps, Max.10A

BEC 3.3V output

  • Designed for Baro / Compass module and Spektrum RX
  • Linear Regulator
  • Continuous current: 200mA

Physical

  • Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
  • Dimensions: 54 x 36 x 13 mm
  • Weight: 26g

Important Notes: 

  • Before soldering or mounting any flight controller, connect it to your PC and verify operation
  • Incorrect soldering techniques will damage this board and void warranty. Please use the correct sized tip, temperature and technique. Temp controlled soldering irons (such as the TS100) are available for under $100 and will make soldering much easier.
  • Lifted pads are a result of incorrect soldering techniques or excess mechanical pressure and will not be covered under warranty. 
  • USB ports must be handled with care, breakage of usb ports are not covered under warranty
  • Always use a smoke stopper before powering your build for the first time. 

Customer Reviews

No reviews yet Write a review

We Also Recommend